howdy, my question is is there any difference between the ev6 style injector in the 1996 and newer explorers and the ones in the 1999 f150 with a 5.4, another question is are the injectors the same so swapping them wouldnt make any difference, and if i do this swap would i see any difference in...

Ok I have finally talked myself into gettin some aussie heads. My question is how much will my compression change and will I have to run octane boosters or premium fuel. I have sealed power 8.5to1 pistons right now. Another question is is will adding these heads affect my torque curve to where...

well the 400 just got sent to the machine shop along with the heads and theyre gonna be ready by next wednesday. plans are bore it .030, kb silvolite pistons, comp xe256 (complete kit), eddy intake, holley carb, and completely rebuilding the tranny and throwin a shift kit in. it outta be pretty...

ok fellas im looking at doing a swap in the bronco but i really cant seem to find all the info i need. i have no clue if the driveshafts need to be lengthened, do i need to get a 2wd np435 or 4wd. so any and all information is greatly appreciated

ok so i got a 390 freshly built and kinda wonderin what #s im lookin at. stock rotating assembly, flat tops, stock heads stock valve train, eddy performer rpm cam. 572 lift 296 duration 236 at 50 thousandths, performer intake and 770 holley street avenger. thanks all

we really need a alabama chapter. although we may not have enough people for that lets give it a try

ok fellas im about to rebuild my 400 and im looking for recommendations for the fuel injection i plan on using. im trying to hold out until holley comes out with the avenger setup so heres what i plan on doing. comp xe256, re ring pistons, crank kit, msd ignition (possibly), (eventually) roller...

well i want to go ahead and do the upgrade so i can stop the bronk a little better only problem is i have a brand new booster and master cylinder on and i dont want to just waste money. anybody want it

ok fellers i recently put a 4bbl on my 351m. the only thing i did different when installing was i used felpro cork rubber gaskets instead of a valley pan. now it knocks terribly when it gets warm. and in gear its sounding like its getting no oil at all. if you throttle it to about 1-1200 the...

alright i recently got a super cooling radiator and my old shroud is too small is there any places other than dennis carpenter and JBG to get them. only reason is i dont want to pay $120 for a shroud that is going to be seeing mud every weekend. thanks

alright I been lookin around lmc and JBG for a 73-77 grille for my bronco but i cant seem to find em, they got 78-79 grilles all day long and ive seen the grille inserts for em but not the grille itself. if anybody knows where i could get one preferably steel not aluminum it would be greatly...

well i am gonna get a 4spd but i do not know what would be the best. i dont really know what the main difference is between the t-18 or np435. i was on JBG and the only major difference i saw was the the t-18 had a higher first gear ratio and it was like a inch shorter i think. but that is why i...

does anybody know the specs of the ford factory camshaft in the 351m/400

ok. i need more torque for my bronc went through a hole yesterday and couldnt even turn a tire in 4h i am going to put headers and gasket match heads and intake. may decide to put a 4bbl on later. it has a 351m but i might go to 400. so for right now i just want to know what i can do to get more...

well ive been doin a little lookin and i was wantin to get some summit headers for my 78 bronco but i dont know if it will affect my ground clearance because they are full length. and they dont make shortys for them. so does anyone know if the full length summit headers will hang down too low...

ok so heres the deal my dad and i want to restore my grandfathers old 65 swb. but we want to convertit to 4x4 and we would like to put it on a 77-79 swb frame. so if anybody could help bout a frame please let me kno