Hi all, wondering if anyone could provide pics of how much the stock wheels and tires stick out on the front of a '65 or 66 compared to a '61-64?

I just got myself an '88 S10 T5 trans with the .72 OD gear. It was $100, a deal I couldn't pass up. My F1 already has a 3.25:1 9" rear. I'm using a stockish 239cid EAB flathead. Tires are 215/85/R16. Overall appearance is to make it look stock.With the .72 OD, my 65mph rpm is 1659. If I...

I'm sure everyone's already off and running to the feast, but thought I"d take a moment to give thanks.Happy Thanksgiving everyone!

I finally got my F6 home. It only took a few years, but today it seems the wait was worth it. It's a 158" WB, 2sp. rear end, 1C for color (offwhite of some sort, painted reddish orange on the outside), has an assortment of lockring 20's and WM's, crashbox 4sp., and a 7H I6 replaced by an EAB...

Hi all, I know this won't get seen much, but I thought I'd throw a feeler out there for anyone who happens to know where I can find a 142" WB '57-60 Ford truck. These would be in the F500 or F600 range. Thanks!

I'll start off with the F6 as it waits to be loaded on a trailer and hauled away to a friend.

Can someone put an angle finder on their engine perches? I'm trying to find two angles and a measurement:#1: the surface the mount bolts to is 45 degrees facing each other?#2: the angle is leaning back about 4.5 degrees, or is the perch level with the frame (not where it bolts over the top...

If anyone has a '73-77.5 F150 4x4 frame, I would like to know the distances between centers on the top bolt holes for the frame perches. Thanks.I measured a highboy F250 and came up with 2.5" center to center. I'm curious to know if the half-ton is different or if they use the same bracket?

Anyone got measurements for the frame on a 4x4 F150? Here's what I have at the engine mounting area:1: outer frame rails across at 34" 2: inner frame rails across at 28.5" (behind engine perches and reinforced area) 3: inner vertical area between perches at 26.5" 4: perch bolt holes centers...

Hi all, I'll keep it short.1: '67-72 front clip and cab is supposed to fit on a '73-79 chassis, right? Just the bed won't work? Just want to verify this, as I'm looking to replace the body on my '79 Bronco plow (w/swapped in 300 6) I know the axles are wider, but no big deal for me.2: Are...

FE/300 and 302/351/400 perch pics wanted for 2wd and 4x4. I'm looking to build my own frame section but don't want the full crossmember of the 2wd, and don't want the bigger perches of a 4x4. What I do want to use, are 2wd perches and motor mounts on a 4x4-like frame. This is for an engine...

Been seeing a lot of good deals on the local craigslist for used (generations 8 & 9) F150's and 250's lately. I'm not so sure the ZF 5 sp. was in an F150, but what all trucks did they come in, and what years specifically? Most typical ads only say 5 speed, and they don't know which is which...

Howdy all, been wondering what the frame width (outside to outside) on both the front and rear are, and what the stock track width is front and rear. thanks in advance. 4x4 and 2wd the same?

Really I am. I'm just dropping in here to put up my official newbie post/thread :hammer: A big hello to everyone here!!

What is going on?Nice to see another site to spend my time on instead of working in the garage, lol. smilieeatndrink