I have had a dead draw on my 85 F-350 7.5L for awhile now. I have not been able to locate it. Tried a test light and pulling the fuses, no help. Tried a multi meter, but I'm not sure if I'm using it correctly. The other electrical problem I am having is occasionally when I try to start it, it...

85 f350, It will start cold just fine, but after getting to temp it won't fire. It cranks fine just won't fire. Getting plenty of fuel, and i checked the coil by putting a spark plug on it. When cranked I didn't see any spark until the key was let go of, then i would see one tiny little spark...

Everybody said it would happen, and it did. I broke my driver side axle. It's a Dana 44, but I have no idea what it's out of. So if anyones got any suggestions of how to tell, I would appreiciate it. Ultimately I would like to get a Dana 60, but they are hard to find around these parts.

Getting ready to swap out a 302 for a 351W in a '84 F-150. I think I have everything I need, but thought I'd see if there is anything I should be looking out for. 302 is EFI, 351W will be Carb'd. He wants to take the heads off the 302 and put on the 351W. I put a gear to gear timing set up in...

Looking for a set of headers that will work with a 460 and 4x4. I figure shorties will fit the best, but I'm having a hard time finding them. It's in a '85 f-350. Any info would be a big help, and thanks.

So I have been fighting a oil pressure issue. It is better with the new high volume oil pump, but not fixed. Then this week I was heading to work and the truck just died. Tried to restart it and it back fired so bad it blew some paint off the valve cover. Distributer gear was missing 4 1/2 teeth...

Replaced my oil pump, everything said don't force it in to place, so i didn't. it fell into place just fine. I turned the motor over by hand, but couldn't see the pump shaft moving. how do i know it installed properly. 460 by the way, in a F-350.Thanks

I am having an issue with oil pressure. It's a 460 and at start up it runs about 60lbs no matter the rpm. After reaching operating tempature it drops to about 25 lbs. at 2000 rpm and 12.5lbs at idle. I was thinking it was oil pump but i don't want to just start throwing parts at it. Any thought...

I'm having an issue with my oil pressure. It's a 460 and at start up it runs about 60 lbs. regardless off rpm. When it heats up it drops to about 25 lbs. at speed (55 mph or 2000rpm) at idle it's around 12.5 lbs. Any ideas? I was thinking oil pump, but I really don't wan to be throwing parts at it.

I'm having trouble getting the cranshaft bolt loose, any tips? I'm trying to get to the timing cover so i can replace a gasket that blew out on me last night. Any tips for removal of the pulleys and balance would be appreciated as well.Thanks

He's got an 04 F150 got the 4.6. Replaced the fuel pressure sensor. Truck was spitting and sputtering, then finally died. He replaced the sensor like I said, and it started right up sounded good, he put in reverse made about three feet and it died. Wouldn't even crank after that. He's trying to...

I am doing research to find a 5 speed ZF transmission for my '85 460. Everything dates '87 and up. So are these still compatible with my block? If not what should I be looking for? I would like a good 4x4 5 speed tranny.Thanks

I am looking for new rear doors or door skins for my 85 f350 crew cab. All LMC carries is the fronts. I've searched and searched on the web but can't seem to come up with anything. Anybody got someplace to go? Thanks.

I am thinking about a body lift. Not sure what all is involved. I know the kits are pretty cheap, but it seems like all you get is the blocks and hardware for them. What else do I need. I am guessing i need to raise the motor or replace the fan with electric.

It's a 1985 F-350 460 cu. in. C-6 Tranny NP205 Transfer Case. Here's the plan: since the truck is a 2wd made into 4wd by previous owner there is a lot to fix. Leaf springs need moved out shocks need installed front drive shaft needs installed. I am thinking about a doubler transfer case already...

Hello everyone. I have a 1985 F-350 460 cu. C-6 tranny NP205 transfer case. On 35X12.5x16.5 BFGoodrich. I am new to the 4X4 world and have many questions that I hope I can gets some help with. I look forward to chatting with all of you.Michael