My brother had this question and since I don't have a clue maybe someone here does. Will a transmission-transfer case from a 98 Expedition with a 5.4 fit a 2000 Superduty with a V10?

Anyone know of a source for a replacement in cab tank? Or of a tank that would fit in the narrow frame of a high boy? Every place I have checked only shows tanks for the rear of the normal width frames and the mid ship tanks for 2X4 trucks. My brother changed the cab and put a 78 cab on it. He...

I acquired an 86 F-150 that had been parked for a couple of years and due to the ethanol gas, the tank and sending unit were rotted out. The truck was a factory 300 6cyl so it was not fuel injected. From a little research, it appears that they changed the sending unit hole in the tank in 85 to...

My brother acquired a 97 Mercury Mountaineer 4X4 with a 5.0. He also has a 99 F-150 with a V6. He wants to move the engine/trans and PCM out of the 97 and put them in the 99. Any ideas what other road blocks/incapatablilties he might encounter?

I just swapped out a 302 C4 combo and replaced it with a 360 C6 combo. Does anyone know if the speedometer drive gear on the end of the cable is different between the 2 transmissions? My speedometer doesn't work and I don't want to tear into things if it is because the gear from the C4 is wrong...

I ordered a Walker Y Pipe Part No 40516 from Advance Auto Parts for a 74 F100 360 2 wheel drive and it is only half of the Y and connects to the left manifold. Every place I have checked lists that same part as the Y pipe including Walkers web site. I'm not having much luck finding the other...

Just ran the vin on a 76 and got this: "Vin decodes as a 1976 F100 2WD Pickup built at the Norfolk plant in August 1976 and powered by a 8 cyl 330 cid 2-bbl engine." I haven't heard of a 330 engine. I'm guessing its a typo but checking here for info if it isn't.

I just swapped 390's in my truck and the replacement has the big hole for the thermostat and the old one had the small one. The casting number on the block is for 67. I talked to NAPA and they said I would probably have to find a water outlet for a 352. Anyone know where I might find a water...

Looking for a pitman arm for a 78 F150 4X4. When I got the truck the pitman arm flopped up and down. Took it off by hand (no puller) cleaned the splines and tried to reinstall it by adding another washer between the nut and the arm. it still moves a little but its better. I'm hoping that the...

I have a 93 F150 302 that I am tired of electronics issues. Will a carb and intake bolt on this? I plan on eliminating the computer as well so I will be changing the dist. I also know that I will have to regulate the fuel pressure so I don't need that info. Just need the info on the intake swap.

Trying to find a source for the gromets that hold the F150 emblem to the cawl on a 78. Its the plastic piece that the pins on the emblem go thru. Anyone know where they can be found?

I have a 351M that I converting to a 400 by swaping the crank and pistons. My question is, are the harmonic balencers the same on the 351M and 400?

I have a 78 F150 4X4 that I have torn down to restore from the frame up. Today I found that the frame is cracked at the steering box and the frame flexes when the steering wheel is moved. I know they make a kit for chevys with this problem but can't find one for a ford. Does any one know of a...

I'm trying to ID an FE without trearing it down. The block casting is C7ME-A and the head castings are C8AE-H which I already know means that it could be any of the FE's. The serial (vin) number on the left rear is 8G124734. Can any one direct me to a place to ID it by that serial number?

I have read on several sites that the only way to tell the differance in these to engines is the either check the casting number on the crank or put something in the spark plug hole and check the stroke. A person that I trust on fords told me that an easy way to tell is to look at the oil dip...