I like the first one, not so into the american flag decals. Anyone know where to get the original ones for the 87-91 4x4?

I'm happy to announce my 4 low works again. Turns out it was the speed sensor on the transfer case. Its a part a had to get from the dealer, but I had to have it. Hopefully it will last another 18 years.Thanks for all the info...

I agree with the remove the rivets method but i used a grinder to remove the heads then replaced them with grade 8 bolts. This makes it easier to service in the future and also will help when I install my lift. But the whole setup sucks to begin with...

Hey Guys, I just came across a 88 bronco thats being parted. It has a 5.0 with the AOD trans and a borg warner 1356 manual shift t-case. I was curious to know if that t-case would be a direct bolt in for my f-150. I currently have a 5.0 with the e4od with the electric shift borg warner 1356. I...

The switches I'm talking about are the shift position sensor switches that tell the computer what position the transfer case is in. I think they are located in the shift motor themselves but I'm not sure.Smokey, do you have a link to the write up? I will try and search for it. The problem I'm...

Does anyone know of a thread for disassembling and cleaning the transfer case shift position switches? I think that may be my problem...Even with all this trouble I still love my push button shift, wouldn't trade for manual shift if someone did it for me.

Does anybody know where to get a 4x4 module and is it a separate module by itself? I cant seem to find it at the autozone....

I have two trucks with the same problem... My 91 5.0 E4OD and 93 5.0 E4OD are bot suffering from a 4wd problem. The push button 4wd works perfectly in 4 high but will not work in 4 low. I have tried to shift them both in nuetral and in park but the 4low will not shift in. Has anyone else had...

I do have the balancer from the explorer and the old balancer from the truck, I could compare the timing marks relative to the key way and see iif they are the same. Not sure if the pointer on the two mount in the same location though.Don't have a intake tube for the airbox yet but plan on...

I played with the air tube today and reconfigured it. I also built an aluminum box to hold the air filter, k&n cone. Have to fix an exhaust leak in the morning and re-check the timing. I have an E4OD tranny.

Has the gt40 heads not the p heads. Only mods are MAF conversion and 3" single exhaust. All MAF stuff from 95 f150 5.0. I used all the stuff from the truck engine, intake, timing cover etc...

I set the timing to 10* BTC and the truck starts and idles well but doesn't seem to be developing the power it should. Almost no torque, revs good in neutral but sounds and feels like its bogged down when I pull out on the hwy. I bumped it up to 11* BTC and it has more power but still feels like...

Yea I used everything from the truck engine. Timing cover, marker and harmonic balancer. I think my dist must be off a tooth or two. Im going to go mess with it.

Hey, I am trying to set the base timing on my new engine and just had a thought. I installed a 1997 explorer 5.0 in my 91 f-150 and used a new(reman) harmonic balancer for a 91 truck 5.0 mostly because of the pulleys not lining up. I am trying to figure out if the timing marks would be the same...

Exhaust is done... new y pipe into single 3" high flow cat with single magnaflow 3" 5x8 oval with a turn down. Sounds great and looks good too.

I have used magnaflow in the past with good results, but i'm not looking for big sound, just nice mellow sound. When I can afford it I plan on magnaflow high flow cats. I just need to put something together with what I have now with a new muffler and I will do a turn down behind the muffler till...

Hello,Just finishing up the install of my explorer 5.0 with MAF conversion in my 1991 f-150 4x4, E4OD. I used the truck exhaust manifolds for now, I still have the factory Y pipe but have reduced it to a single cat. I have heard good things about the flowmaster 50 series and am thinking of...

No have not posted in FSB yet, but have found some good info on there about this issue. Apparently there were alot more e4ods in the later broncos than the trucks. More common to have 4r70w in the truck. The last diagram helped alot, it shows the wiring configuration for the 12pin e4od...

Hey Alvin, Thanks for the info. I have reliable information that way1 computer is for 94-95 f-series 5.0 with federal emissions, MAF and E4OD. The 5.8 computer equivalent is a lay1. But they are wired differently. As far as the o2 sensor is wired, pin# 44 is o2 in, black is ground and red goes...

Thanks for the response, my confusion was coming from the diagrams on ford fuel injection. They show a dual O2 sensor setup on the engine harness for 95 trucks but I found out today at the dealer that trucks up to 95 only ran one o2 sensor and then three in 96. The only other question I have is...

Hello to everyone, I am a lifer when it comes to ford I currently have three trucks that run and two that are being restored. My goal is to have a least one truck from every generation. The old ones anyways.Even my lawn mower is a ford!

Sorry guys I have one other question as well. Is pin 49 the the o2 ground on the 95 truck computers as well. The pin out sheet on ford fuel injection shows that pin empty for 94 and 95 but o2 ground for all other years. Where do I groung the o2 sensor?Thanks

If it is the a/c disconnect would it move to a different pin on the 95 computer? From what I have been able to find on maf conversions it seems like the 95 trucks only have one o2 sensor. Is this correct. The write ups say they move the o2 from pin 29 to pin 44. It appears that the mustang...

Here's a thought. For the guys out there with 95 f150's do you have one or two O2 sensors? They swore to me at oreilly that I had two on my 91 according to their computer.

Hello, I am finishing up a MAF conversion on my 91 f150 5.0 4x4 With E4OD. I am using a computer from a 95 bronco its a WAY1. My problem has to do with the O2 sensor. According to ford fuel injection website I have a 3 wire O2 sensor but mine is actually a 4 wire. Also according to them the 95...