All I have found for flares is bushwacker. Not sure how they would look on my bullnose considering its dropped so far.I've started attempting to make steel ones and I'm already hating it.Does anyone know of any other flares out there for a bullnose that aren't god awful looking. I'm about...
The 2wd short bed is currently on hold for now because I've been working on the idi.I'll start with the engine bay still needs a lot but its definitely better.Quality might be poor uploading them this way.
What are typical problems with these old bullnose for the front calipers to drag and get excessively hot?I just did calipers and pads last night because they were sticking so bad the truck would come to a stop when you pushed in the clutch or coasted in neutral. It's still dragging and getting...
Anyone know of brake upgrades for the front. 82 2wdTruck gets raced, it's on 20s and would be nice to have stronger front brakes. I have a parts list together to do a rear disc conversion.
I had to get rid of my dentside but shortly after got this 82. I’ve been wanting to build a short bed for quite some time and this one was bought by a friend and I had to have it. Very well taken care of. Receipts back to the early 90s, oil change schedules since 1990. The whole front suspension...
Is there bearings and such available to rebuild a steering column? Mine is shot. Also anybody know where I could get a new ps pump pulley?Plans for the truck in the next couple months consist of all new vacuum lines and get rid of the inverted y so I can run a pitman arm for the lift that's on...
I need pretty much all new steering. Ill wait on the steering box, but i need everything before and after it including pump...Recommendations on brand? Where to purchase?Ill look at rock auto for linkage and tie rods...Oh and it has to be 78/79 linkage because i REALLY need a drop pitman arm
Want some opinions and such for a new dizzy for my truck.I will be going to an msd coil and 8.5mm wires. May even side gap the plugs as well.Stock dizzy needs replaced, figured if im going to do it i might as well upgrade.Also, are wiring harness still available for the ignition/dizzy...
Ordering my new Holley maybe Friday. Should I do the non adjustable float carb or adjustable float
carb? The non adjustable is 100 less but how much better would the adjustable be?
A guy emailed me saying he's sell me his dele brick performer intake for 100$ it has the thermostat housing and heat hose elbow. What should I look for before buyin it other than any cracks or chips... And what would you clean an intake with? Carb parts cleaner?
if you had 100,000-150,000 to throw into a dent...what year would it be?what trim package?what size 1/2 3/4 or 1 ton?short, long, or stepside?reg cab, sc, cc?what engine? (doesn't have to be ford)if any, what size lift?what size tires/rims?auto or manual?what interior and...
i have two horns on my truck both work, i do not have the insert for my steering wheel with the horn buttons thought about sticking them to a toggle switch or a button on the dash for right now. i can follow the wire up the relay then theres a yellow and one that looks black, where exactly do...
Got a 360 with the C-6. It shifts fine into second but hen I get to the point that it should shift up to third it either won't shift or shifts really hard. Is that a vacuum line or something on or in the tranny?
i bought a couple 100 watt halogen lights to go on my cherokee. it just says to run them through a fuse and the igniton so it won't drain the battery...what size switch would i need to run the two lights with? is a 15 amp switch to little?
bought a manual choke for the truck yesterday, its universal so i expect to run into a couple little snags while installing.
i opened it up and the one that uses the peices from the old auto choke don't seem to fit without modifying the old choke "tang".do you suggest i do that, or keep the...
1976 ford f150 360 fe c6 with column shift
will the flow tech brand headers at summit fit? it says they will but i don't want to get them and end up not being able to use them. i will just take my other exhaust and chop it up for the headers if they work. i will only run the headers for a year...
so i set my timing and the truck was idling good. i was tightening the dizzy down and the truck just shut off. it didn't diesel or sputter. t just stopped. now it won't start.fresh battery, alt, voltage regulator.was tuned up completely in july/ august and carb rebuilt.it hasn't ever done...
what is the engine going to act like with the timing advanced versus the timing to low? is there a noticeable difference?i got the timing in enough that the engine will fire, but... the starter keeps locking up then i shut the key off and the truck will fire up and shut off it will also...
my tdc on my pulley is the number 6 cylinder on the dizzy. the only thing i've done was bumped the timing up a few degrees. it ran fine before and was all lined up. but somehow the pulley and dizzy are way off. how do i fix it?
i made a knob for my blinker, and monday going to turn a dirt bike piston into a t case knob.does anyone have any other ideas? i will eventually do something with the pedals as well.i don't really wanna waste my money buying anything but i do have tons of old parts and scrap and everything else.
I'm kind of debating on engines and gear ratios for my truck.
What engines do you guys run?
What mods?
Axle ratio?
Tire size?
And approx mileage in city and on highway?I'd even like to hear gen. 5 and 7 trucks as well.
My truck had a slight whistle coming from brake booster got that fixed put a block of plate on the egr valve and for some reason the carb is now whistling like a tea kettle and only gets louder when I give it gas. It's louder than the truck and it has 5 foot straight pipes. What could it be...
i have 35x15.5x15 swampers 90% tread. they weigh 84 pounds a piece.i kind of want to go bigger. the 36x12.5x15 tires are 12 pounds lighter per tire.. does that make much of a difference in performance?
i guess i'll do a build thread, not sure where to start. i won't be doing a frame off resto until maybe next winter. need to find another vehicle to use as a dd before i can go too deep into this one. for now i'm just going to replace the front clip, fix the electrical issues, and replace a few...