Prime, I have thought much over your advise. I agree that making a good running truck into a pile of parts sure doesn't sound appealing. I believe I will save and buy my intake first. I will then save again and purchase my carburetor. I have decided on the Edelbrock intake and the Holley 4150...

Hey Gents. Hoping your Thanksgiving was great. Ours always is as mom goes all hog on Thanksgiving. I ate so much I nearly put myself in the hospital.Anyhow, my 352 is a royal 8ltch an a 1/2 to start in the morning. I don't know if it's just it's nature? Or, I am flooding it? To much choke...

I wanted to add that I also sprayed the inside of the compartment with the rubberized spray can of where the heater coil came to rest against metal areas. It worked out to a snug fit. I also padded the tubes that went through the firewall into the engine compartment. Some kind of grommets would...

Hey Ben, I personally would grade the replacement of the heater core in a 1967 f250, 4WD without A/C. Once I sat back and really took a look at the job it got easier as I thought about it and really got serious about getting it done. 1-10, with 10 being the toughest. For me, it was a 3...

Guys, there have been a lot of changes in my plans since this last election. I won't get into it as that's probably just another road to get me tossed out of here. As some may remember I have stated that I had plans for the military after graduation. I was sure as the heat in hell that Obama...

Ok guys, do I 'need' a 4-bbl intake to change from 2 to 4bbl? Or, can I use an adapter plate? Are those adapters just a joke? Or do they function as intended? ThanksDTM

Hey, I'm just a kid (I guess) My opinion never goes very far in my family any way. But I like what my Grand dad says. Whatever you are looking to buy is exactly worth what you are willing to pay for it. Not what the guy is asking for it. It's a ton of eye candy that I am years away from...

I got it guys! The old one was copper. The new, aluminum. All is good, no leaks. Hey, I kinda tore up the cardboard box glove box liner getting it out. But I fixed it nice! Looks awesome! I used gorilla tape to piece it back together. Then I sprayed it all over with the rubber stuff you like use...

Heater coilI took the box out of the glove compartment today. That was terrible in it's self. Someone had glued it in and I had to tear it to pieces to get it out. That severely bummed me out! I hate to say but no, it was not 'right there' all I saw was the top of the blower housing. The coil...

Looking for an intake for my 1967, 352. Stock manifold or an aftermarket aluminum would be even better (shipping) Also will be looking for the 4bbl carburetor to go on it. Thanks for any consideration.DTM

Thanks Gentlemen,Hey Roy, I still have the 'bag' that holds the windshield washer fluid. Kinda cool huh? And it doesn't leak! Yea, that's a good plan. I think I'll just drain all coolant and replace with new. About a half & half mixture, correct?Also, my tires have like 80 pounds in them...

I thank ya Ben. I'll get after it this weekend.

Guys, I assume this is my heater core? When I started it this morning (I do this sometimes before I catch the bus for school) When it warmed up, steam covered the windshield. I would like to know how would you rate this job. Is it a difficult repair? Do you suppose it's something I can handle...

Intake & CarbsI did find a nice set of headers. DNFXDLI, the 600-650 you speak of...Would a Holley be the answer? Not like a 'double pumper' correct? Could you be a bit more specific? 600 OR 650. On a 'vacuum secondary' does the secondary's require adjustment, like when they begin to open? Or...

Intake & CarbI would like to ask this again. Do you folks recommend an intake and a four barrel carburetor for my stock 352? Thank youDylan