What did you work on today

heavydoc · Jul 14, 2020

I think she got a little warm

Sent from my iPhone using Tapatalk

fatherdoug · Jul 14, 2020

Sorry, but what am I looking at?

heavydoc · Jul 14, 2020

fatherdoug said:
Sorry, but what am I looking at?

That is the torque converter housing on the transmission of a 824J John Deere loader

Sent from my SM-N975U using Tapatalk

Blue-Truck-Nut97 · Jul 14, 2020

Looking good!

What exactly were you wanting me to polish?

Sent from my E6810 using Tapatalk

heavydoc · Jul 14, 2020

Looking great, those are the same wheels on my Excursion, salt pits and all..... Charlie are those my Excursion wheels?

Sent from my SM-N975U using Tapatalk

heavydoc · Jul 14, 2020

Blue-Truck-Nut97 said:
Looking good!

What exactly were you wanting me to polish?

Sent from my E6810 using Tapatalk

It's called a knob[emoji1787][emoji1787]

Sent from my SM-N975U using Tapatalk

Blue-Truck-Nut97 · Jul 14, 2020

heavydoc said:
It's called a knob[emoji1787][emoji1787]

Sent from my SM-N975U using Tapatalk

Betting he could find somebody cheaper and prettier than me.....

Sent from my E6810 using Tapatalk

heavydoc · Jul 14, 2020

Blue-Truck-Nut97 said:
Betting he could find somebody cheaper and prettier than me.....

Sent from my E6810 using Tapatalk

[emoji1787][emoji1787][emoji1787]

Sent from my SM-N975U using Tapatalk

fatherdoug · Jul 14, 2020

heavydoc said:
That is the torque converter housing on the transmission of a 824J John Deere loader

Sent from my SM-N975U using Tapatalk

Thank you.

heavydoc · Jul 14, 2020

fatherdoug said:
Thank you.

No problem, I could have put a pic up of the machine buuuuuttttttt......

Sent from my SM-N975U using Tapatalk

Blue-Truck-Nut97 · Jul 14, 2020

By polish wheels you mean rattle can flat black right?

Sent from my E6810 using Tapatalk

dustybumpers · Jul 14, 2020

Um. No. I actually think old skool muric acid, wash, then polish out wit my homemade polish
Here's tank on owmbo's Pete I did a bit back

Sent from my SM-N960U using Tapatalk

heavydoc · Jul 18, 2020

Fan drive hub bearing replacement on a 824J JD quarry loader

Sent from my iPhone using Tapatalk

heavydoc · Jul 18, 2020

Took me a bit to find this one, that harness runs through the articulation section of a 544L loader. It is fully covered in a protective hose layer. Cut the hose off and did a 10 lb pull test on the 39 wires in that harness. 30 of them broke. It only had 1 code and was intermittent

Sent from my iPhone using Tapatalk

heavydoc · Jul 18, 2020

Pulled the cab to replace the internal transmission harness cause the transmission temp sensor was reading very hot. That sensor is made into the harness

Sent from my iPhone using Tapatalk

heavydoc · Jul 18, 2020

Sent from my iPhone using Tapatalk

heavydoc · Jul 18, 2020

This was a fun one, at the top of a sand pile and threw the left track off to the inside on the sprocket and idler end. I was there to fix a hydraulic thumb issue. Owner was pissed when I told him about it. The trackhoe wasn’t even supposed to be up there. In fact the operator was told specifically not to climb the pile

Sent from my iPhone using Tapatalk

SuperCab · Jul 18, 2020

I like those 844 loaders. Maybe wouldn't if I had to work on one though :rofl:

heavydoc · Jul 18, 2020

They aren't so bad, the 744's have a ton more room around the engine to work on

Sent from my SM-N975U using Tapatalk

SuperCab · Jul 18, 2020

heavydoc said:
They aren't so bad, the 744's have a ton more room around the engine to work on

Sent from my SM-N975U using Tapatalk

744H is one of the best loaders I've run. Thing was rough and noisy but man it would load trucks

Join Our Ford Truck Forum Today

What did you work on today

Instigator

Tonto Papadapolous

Instigator

crank polisher

Instigator

Instigator

crank polisher

Instigator

Tonto Papadapolous

Instigator

crank polisher

don't play well w others

Instigator

Instigator

Instigator

Instigator

Instigator

Moderator

Instigator

Moderator